« previous next »
Pages: 1 2 3 [4] 5 6

Author Topic: Natalie 2 Skeleton failure  (Read 8407 times)

0 Members and 3 Guests are viewing this topic.

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #45 on: November 15, 2021, 04:49:49 PM »
I've peeled back the silicone to check out the weld on the other side, and it looks good.   I am a bit concerned though, if I ought to shorten the insert on the horizontal section if I might ever need to perform the same operation on the other side. 

I am going to be very careful how I use her from now on so as not to over  stress that area.  OK, I've chosen not to cut the inset, iff the other side breaks, I'll deal with it.   



Phil
Logged

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #46 on: November 15, 2021, 07:21:49 PM »
Began by ramming some paper towel into the tube to prevent JB Weld from flowing further down the hole. Using Dad's pallet knife to place gobs of JB Weld into the hole, and gobbing it into the copper pipe section before placing it onto the frame.





I didn't know how much working time I'd have before the stuff started to set up, so began working right away.  Turns out I could've waited
 20 minutes or so, the stuff kept flowing out of the copper pipe. I'd wipe it up and apply more at the top until it stopped flowing. Instructions say it'll set is 4 to 6 hours, but after a half hour it stops flowing though it's still plenty pliable..





That last shot illustrates where the JB Weld stopped flowing. Full cure in 15- 24 hrs. I'll let it sit until tomorrow evening before resuming work.



Logged

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #47 on: November 16, 2021, 07:38:32 PM »
Gad Muther fracking Zook's what a mess this job became!   Now I must sit with her as the JB hardens trying to remove any that's where it shouldn't be. It won't stick to the silicone, that's the saving grace.




The curing JB Weld picks up with a butter knife sticking to the metal far more than silicone.



The curing JB will roll up between the fingers for easy placement to fill where it ran out when runny.





Logged

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #48 on: November 16, 2021, 08:43:03 PM »
......."ohhhh sister morphine....  when are ya, coming' 'round....   again"

Logged

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #49 on: November 16, 2021, 08:48:15 PM »
".........ohhhhh...  an' ah don' think  ah can wait, that long...."

Logged

JB

  • Staff
  • Functional Drunk
  • *****
  • Posts: 172
Re: Natalie 2 Skeleton failure
« Reply #50 on: November 16, 2021, 10:14:10 PM »
The poor baby! :(
Logged

Smoke

  • Inebriation Engineer
  • *****
  • Posts: 638
  • Most humble servant of CJ's Harem.
Re: Natalie 2 Skeleton failure
« Reply #51 on: November 17, 2021, 12:29:56 PM »
Logged
Canadians are generally very nice,until the puck drops.

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #52 on: November 17, 2021, 01:51:02 PM »
I wrapped the copper in electricians tape to be safe, though silicone is supposed to be safe with copper. 

Begining to silpoxy the deepest cuts working one section at a time.  The skin layer will be the last, and that will be done in sections as well to get the best least scared finish.

Logged

JB

  • Staff
  • Functional Drunk
  • *****
  • Posts: 172
Re: Natalie 2 Skeleton failure
« Reply #53 on: November 17, 2021, 02:59:45 PM »
Keep up the good work Phil, when you are done give that poor girl a bath!!!!! I am kidding, I think!
JB
Logged

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #54 on: November 17, 2021, 05:42:37 PM »
Quote from: JB on November 17, 2021, 02:59:45 PM
Keep up the good work Phil, when you are done give that poor girl a bath!!!!! I am kidding, I think!
JB

She needs one.  I'm cleaning her where she lays, what I can reach and powdering.  Will probably finish with closing the incision tomorrow, I'll roll her over and clean her frontally.

Phil
Logged

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #55 on: November 19, 2021, 12:41:00 AM »
Didn't finish closing today, taking smaller steps. Moved her leg though, didn't hear anything pop!  ;)
Logged

Ceej

  • Staff
  • Inebriation Engineer
  • *****
  • Posts: 982
  • Head Bartender
Re: Natalie 2 Skeleton failure
« Reply #56 on: November 19, 2021, 05:00:55 AM »
 :thumb: :thumb: :thumb:
Logged
" Leaving it to the imagination "     is highly overrated.




Sandy is a wonderful B6 Classic Realdoll, and Nicole is a sweet Realdoll Petite 5.  Close sisters, they both share classic F1 faces as well as all the classic F1 expression faces. Sandy also has several sets of reusable "Real Breast" prosthetics.     Julie, Christine, Emma, Kiki and their friends are sexy little Phicen micro-babes.

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #57 on: November 19, 2021, 01:32:23 PM »
One more day should do it.



Logged

Ceej

  • Staff
  • Inebriation Engineer
  • *****
  • Posts: 982
  • Head Bartender
Re: Natalie 2 Skeleton failure
« Reply #58 on: November 19, 2021, 01:35:22 PM »
 :thumb: :thumb: :thumb: :thumb:  Looking good  8)
Logged
" Leaving it to the imagination "     is highly overrated.




Sandy is a wonderful B6 Classic Realdoll, and Nicole is a sweet Realdoll Petite 5.  Close sisters, they both share classic F1 faces as well as all the classic F1 expression faces. Sandy also has several sets of reusable "Real Breast" prosthetics.     Julie, Christine, Emma, Kiki and their friends are sexy little Phicen micro-babes.

Phil

  • Functional Drunk
  • ****
  • Posts: 322
Re: Natalie 2 Skeleton failure
« Reply #59 on: November 19, 2021, 01:38:43 PM »
     "Another day?  I'm really getting tired of lying here...  old man."

Logged
Pages: 1 2 3 [4] 5 6
« previous next »