I want to bring these boobs back to life. Any suggestions?

[Zarnon]

Hey!  This is my WM 162 E that went to customs in Tennessee,  was released and Fed Ex lost it for 3 months.  It was a total cluster fuck and a few weeks after she arrived both breasts deflated.  I got no help from the mfr.  Fed Ex was worthless. 



I'm thinking I will cut at the base of the breast and insert one of these silicone inserts on each side.  The should deform enough so the incision remains small.  I can close with TPE glue:

 

I've read for years how TPE and Silione can cross react but never actually saw any evidence to support this.   Urban myth?

[Ceej]

Sorry to hear of this mess.

I think it does depend on the blend of TPE and Silicone, but as far as I know in the long term,(more than an hour's contact) they do not get along.
One will tend to soak out the oils from the other.

You may or may not know this, but in case you don't, one thing some of the TPE makers do is fill their doll's boobs with air instead of gells.
So perhaps an alternative fix would be to inflate them with air. just enough to fill them, but not so much that they become hard.

[Mr_Hand]

Wow… a $1500 Doll with $3000 silicone implants. 

Good luck with the operation.

[Zarnon]

Wow… a $1500 Doll with $3000 silicone implants. 

Good luck with the operation.

Same concept but the photo I posted are ones  made for women (or men) to put in brassieres.   The ones that go inside people are a higher grade medical silicone as the only difference.   

The ones I ended up getting cost 15 bucks   

https://www.amazon.com/Silicone-Inserts-Enhancers-Swimsuits-Transparent/dp/B07C5YZBKZ/ref=sr_1_2_sspa?crid=2876NM9N36953&keywords=silicone+inserts&qid=1680876833&sprefix=silicone+inserts%2Caps%2C190&sr=8-2-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEyTDhNNFQ3QkpPTlgwJmVuY3J5cHRlZElkPUEwNTczMTM4M0tZUFhVNDRZQkxLSyZlbmNyeXB0ZWRBZElkPUEwMDgzMDc2M1RRSjZZR0ZLM0FKTyZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

I have nothing to lose.  The doll is too unattractive to me at present.   The inserts arrived yesterday.    The one problem I see is they're firmer than the surrounding gel.   I might try again and see if I can get softer before the procedure.

[Begog]

The tits on my WM166C were sagging pretty bad. They are gel boobs, but I have fixed air boobs the same way. First, you need a metal turkey baster. You can pump air in through the nipples. It MAY hold. Likely, it will not. Inject TPE paste into the breast, allow generous drying time.
TPE paste: TPE plus xylene (or tolulene I hear). must be thick. Runny may eat through the doll.

That's a 166D now. 

[Doll_Master]

Boob deflation is my life unfortunately. Since they are hollow you can pump em up with air. I have done this for both silicone and TPE. I used a turkey injector needle. One of those large syringes. for TPE coat it with a little TPE glue. if you don't have that glue try elmers clear. For Silicone coat the needle with Silpoxy. Remove plunger from the syringe tube. Put the needle on it.

Take your time!
Gently go directly down the center of the nipple allowing the needle to break through. Once it penetrates just use your mouth to blow into the boob until the desired size. Then gently pull the needle out and rub your finger over the nip to allow the glue to seal it. Yes there will be a new nipple duct. Which is normal anyway. Do this to both but pay attention. Its easy to make one bigger than the other. And you can go a little crazy for big boobs if wanted. but over inflation can cause a boobie explosion 

Here is one of my girls tits before this method..


And after..


I had to do the same for Mistie. She was a little flat and this method worked just fine. Peace my friend - DM

[Phil]

A great technique DM!

Phil

[Z-Dr]

Bitter Beer Boob!